Crown

Board: Porsche - 911 - 997 Language: English Region: Worldwide Share/Save/Bookmark Close

Forum - Thread

    May 22, 2005 10:44:03 AM

    Prashan
    Co-Pilot
    Prashan
    Loc: London, UK
    Posts: 208, Gallery
    Registered on: Jun 28, 2004

    997 - Front Trunk Lid alignment issue

    Hi All,

    Anyone had an issue with the front bonnet lid not being correctly aligned - I recall there may have been a case or two.

    Why would this happen so early - not really causing me a problem but from the two pictures below - you will note in pic 1 (at the dealer on collection), the alignment is fine. On Pic 2, its slightly out of alignment on the bottom right.

    Regards
    Prashan

    May 22, 2005 10:45:00 AM

    Prashan
    Co-Pilot
    Prashan
    Loc: London, UK
    Posts: 208, Gallery
    Registered on: Jun 28, 2004
    Reply to: Prashan

    Pic 2

    Pic 2

    May 22, 2005 11:34:25 AM

    derder
    Senior
    derder
    Loc: Australia , Australia
    Posts: 593, Gallery
    Registered on: Dec 4, 2004
    Reply to: Prashan

    Re: 997 - Front Trunk Lid alignment issue

    have u by any chance used too much pressure on the lid when closing???
    blame ur wife/ kids for that....

    cos its aluminium. u can potentially deform it if u lean too heavily on it.
    the dealer told me to close lid by applying "firm" pressure on the EDGE of the lid , below the Porsche crest....

    May 22, 2005 12:36:06 PM

    KenH
    Co-Pilot
    KenH
    Loc: Leesburg VA
    Posts: 249, Gallery
    Registered on: Nov 23, 2004
    Reply to: derder

    Re: 997 - Front Trunk Lid alignment issue

    I suspect that it is the plastic front bumper that is the problem.

    May 22, 2005 3:19:09 PM

    MMD
    Rennteam VIP
    MMD
    Loc: usa
    Posts: 9652, Gallery
    Registered on: Dec 16, 2004
    Reply to: KenH

    Re: 997 - Front Trunk Lid alignment issue

    The hood should only be closed by gently pressing on the badge. Put pressure on it until it clicks.

    Also, shouldn;t the gap be the same all the way around? The sides shouod match the front?

    Try adjusting the rubber bumper stops that should support the hood. That's the only thing you can do. Moving the hood or the bumber itself, even slightly, will result in major gap inconsistencies.

    May 22, 2005 4:08:24 PM

    Mike S
    Rennteam VIP
    Mike S
    Loc: Somewhere , Taiwan
    Posts: 7720, Gallery
    Registered on: Apr 3, 2005
    Reply to: MMD

    Re: 997 - Front Trunk Lid alignment issue

    Quote:
    MMD said:
    The hood should only be closed by gently pressing on the badge. Put pressure on it until it clicks.




    My dealer said exactly what Derder's dealer said, they also told me specifically "not" to press on the badge but more below, right on the edge.

    May 22, 2005 4:17:37 PM

    Steven Martins
    Junior
    Steven Martins
    Loc: Oporto, Portugal
    Posts: 145, Gallery
    Registered on: May 10, 2004
    Reply to: MMD

    Re: 997 - Front Trunk Lid alignment issue

    My 987S has exactly the same "problem". I haven't yet talked with the service manager about it but it does seem to be front bumper that is somehow creating this problem.

    I have to take a few pictures of it.... More than 3 weeks of ownership and haven't yet taken a single picture :/

    May 22, 2005 4:19:35 PM

    throt
    Rennteam VIP
    throt
    Loc: London , United Kingdom
    Posts: 6083, Gallery
    Registered on: May 9, 2005
    Reply to: Mike S

    Re: 997 - Front Trunk Lid alignment issue

    I was told for closing drop the lid from around 6-7inches , pushind down on a lid waiting for the click can cause slight dentation ..

    I have seen this happen to bonnets before but the alignement ? well has someone pushed hard on the right ( as we look ? )..

    Have a word with the dealer..

    throt.

    May 22, 2005 4:43:01 PM

    Steven Martins
    Junior
    Steven Martins
    Loc: Oporto, Portugal
    Posts: 145, Gallery
    Registered on: May 10, 2004
    Reply to: throt

    Re: 997 - Front Trunk Lid alignment issue

    Some another comment I forgot to include before... This front trunk lid alignment issue was already present when I picked up the car. I did not discuss this at the time because I was already way to late for me and it's something that they can't accuse me of doing since the sales person saw it when I mentioned it.

    May 22, 2005 4:46:23 PM

    Prashan
    Co-Pilot
    Prashan
    Loc: London, UK
    Posts: 208, Gallery
    Registered on: Jun 28, 2004
    Reply to: Steven Martins

    Re: 997 - Front Trunk Lid alignment issue

    Thanks all for your feedback - I have been taking care in applying light pressure just below the bagde when closing. Considering the bonnet is such a larg part of the car, the locking latch seems quite weak.

    Will ask dealer to look at it next time I'm in.

    Regards
    Prashan

    May 22, 2005 4:58:13 PM

    grant.uk
    Junior
    grant.uk
    Loc: UK
    Posts: 101, Gallery
    Registered on: Feb 1, 2005
    Reply to: Prashan

    Re: 997 - Front Trunk Lid alignment issue

    My bonnet was out of alignment when i picked up the car, i took it back and they sorted it!the bonnet should always sit slightly below the level of the bumper this is so that the wind pressure does not get under the bonnet at high speed! hope you get it sorted mate..

    May 22, 2005 6:46:18 PM

    Prashan
    Co-Pilot
    Prashan
    Loc: London, UK
    Posts: 208, Gallery
    Registered on: Jun 28, 2004
    Reply to: grant.uk

    Re: 997 - Front Trunk Lid alignment issue

    Cheers Grant - sorry for not getting around to organise the UK meet - been a tad busy changing jobs and stuff.

    Will do soon
    Prashan

    May 22, 2005 7:05:13 PM

    jfraser
    Co-Pilot
    jfraser
    Loc: LA
    Posts: 267, Gallery
    Registered on: Feb 1, 2005
    Reply to: grant.uk

    Re: 997 - Front Trunk Lid alignment issue

    MMD said:
    The hood should only be closed by gently pressing on the badge. Put pressure on it until it clicks.

    This one I can answer categorically.....about 6 weeks ago I had 3 engineers from the factory (actually two from the factory and one from their electronics supplier,) looking at my car. When I closed the lid by pushing down on the badge one of them told me not to close it that way. He said that you can crack the lid ....There are a couple of holes beneath the badge where the pins locate...Under certain conditions (by repeatedly pressing on the badge) the holes generate cracks.....He said he'd seen cars where the cracks caused a split from one hole to the other (I believe the holes are a diaganol from one another).....You should gently press belowthe badge (to the left, center, or right )...

    May 22, 2005 10:26:12 PM

    MMD
    Rennteam VIP
    MMD
    Loc: usa
    Posts: 9652, Gallery
    Registered on: Dec 16, 2004
    Reply to: jfraser

    Re: 997 - Front Trunk Lid alignment issue

    Quote:
    jfraser said:
    MMD said:
    The hood should only be closed by gently pressing on the badge. Put pressure on it until it clicks.

    This one I can answer categorically.....about 6 weeks ago I had 3 engineers from the factory (actually two from the factory and one from their electronics supplier,) looking at my car. When I closed the lid by pushing down on the badge one of them told me not to close it that way. He said that you can crack the lid ....There are a couple of holes beneath the badge where the pins locate...Under certain conditions (by repeatedly pressing on the badge) the holes generate cracks.....He said he'd seen cars where the cracks caused a split from one hole to the other (I believe the holes are a diaganol from one another).....You should gently press belowthe badge (to the left, center, or right )...



    I'm sorry guys; I screwed up here. You're probably right. The "Badge Press" is how I close my 03 986S. Makes sense on the Boxster since the hook is directly underneath it. OOPS!

    May 23, 2005 5:48:38 AM

    Mike S
    Rennteam VIP
    Mike S
    Loc: Somewhere , Taiwan
    Posts: 7720, Gallery
    Registered on: Apr 3, 2005
    Reply to: MMD

    Re: 997 - Front Trunk Lid alignment issue

    now at least i know my dealer is properly trained

    May 23, 2005 2:54:21 PM

    John SF 2005 997 S
    Senior
    John SF 2005 997 S
    Loc: San Francisco CA USA
    Posts: 530, Gallery
    Registered on: May 14, 2004
    Reply to: Prashan

    I'm sure that can be adjusted easily...just ask your service

    Person.... the height can be adjusted by the little rubber bumper things under the hood...
     
    Edit

    Forum

    1. All 

    Boards

     
    Board Subject Last post Rating Views Replies
    Porsche Sticky SUN'S LAST RUN TO WILSON, WY - 991 C2S CAB LIFE, END OF AN ERA (Part II) 5/15/24 8:44 AM
    art.italy     		811805 1808
    Porsche Sticky Welcome to Rennteam: Cars and Coffee... (photos) 4/7/24 11:48 AM
    Boxster Coupe GTS     		452591 565
    Porsche Sticky OFFICIAL: Porsche 911 (992) GT3 RS - 2022 3/12/24 8:28 AM
    DJM48     		271192 323
    Porsche Sticky The new Macan: the first all-electric SUV from Porsche 1/30/24 9:18 AM
    RCA     		91763 45
    Porsche Sticky OFFICIAL: Taycan 2024 Facelift 3/15/24 1:23 PM
    CGX car nut     		8516 50
    Porsche The moment I've been waiting for... 2/1/24 7:01 PM
    Pilot
     
     
     
     
     
    		 890674 1364
    Porsche 992 GT3 7/23/23 7:01 PM
    Grant     		847962 3868
    Porsche GT4RS 4/21/24 11:50 AM
    mcdelaug     		404151 1454
    Porsche Welcome to the new Taycan Forum! 2/10/24 4:43 PM
    nberry     		400732 1526
    Others Tesla 2 the new thread 12/13/23 2:48 PM
    CGX car nut     		387993 2401
    Porsche Donor vehicle for Singer Vehicle Design 7/3/23 12:30 PM
    Porker     		372803 797
    Porsche Red Nipples 991.2 GT3 Touring on tour 5/12/24 6:23 PM
    blueflame     		295169 669
    Porsche Collected my 997 GTS today 10/19/23 7:06 PM
    CGX car nut
     
     
     
     
     
    		 269590 812
    Lambo Huracán EVO STO 7/30/23 6:59 PM
    mcdelaug     		245343 346
    Lotus Lotus Emira 6/25/23 2:53 PM
    Enmanuel     		239628 101
    Others Corvette C8 10/16/23 3:24 PM
    Enmanuel     		223790 488
    Others Gordon Murray - T.50 11/22/23 10:27 AM
    mcdelaug     		174305 387
    Porsche Back to basics - 996 GT3 RS 6/11/23 5:13 PM
    CGX car nut     		145953 144
    BMW M 2024 BMW M3 CS Official Now 12/29/23 9:04 AM
    RCA     		122594 303
    Motor Sp. 2023 Formula One 12/19/23 5:38 AM
    WhoopsyM     		114646 685
    Porsche 2022 992 Safari Model 3/7/24 4:22 PM
    WhoopsyM     		86885 239
    AMG Mercedes-Benz W124 500E aka Porsche typ 2758 2/23/24 10:03 PM
    blueflame     		77167 297
    Porsche 992 GT3 RS 3/3/24 7:22 PM
    WhoopsyM     		56305 314
    Motor Sp. Porsche 963 5/18/24 9:44 PM
    Wonderbar     		28057 249
    Ferrari Ferrari 296 GTB (830PS, Hybrid V6) 1/21/24 4:29 PM
    GT-Boy     		22693 103
    BMW M 2022 BMW M5 CS 4/8/24 1:43 PM
    Ferdie     		21456 140
    AMG G63 sold out 9/15/23 7:38 PM
    Nico997     		17905 120
    AMG [2022] Mercedes-AMG SL 4/23/24 1:24 PM
    RCA     		15948 225
    Porsche Porsche Mission X Hypercar 12/3/23 8:52 AM
    996FourEss     		11835 63
    Porsche 911 S/T 10/10/23 8:53 AM
    RCA     		11147 55
    117 items found, displaying 1 to 30.